What Causes Water Pressure to Decrease?

November 21st, 2018

what causes water pressure to decrease

What Causes Water Pressure to Decrease?

Low water pressure can be frustrating as it has an effect on your daily life. From use in the kitchen to the shower, low water pressure can make a task as simple as washing the dishes a nightmare.

So what causes water pressure to decrease? We have 6 common reasons why most homes face water pressure issues.

Water pressure issue #1: Issue with the water valve

Two valves control most homes water flow. If you face water pressure issues, you want to check these valves first. They are usually near the water meter. The valve that is positioned on the street side is the city’s, you may not have access to this since it belongs to the city. The other valve, which is on the side of your home, controls the water in your home.

You want to make sure both the valves are completely open. They control the water flow into your home so if it is not completely open then chances are you will have low water pressure. When operating the valve, you need to be gentle with it. Don’t apply too much force, which can cause damage.

If access to the city valve is cut off then you can contact the city office and see if they can send someone down to open it for you.

Water pressure issue #2: Fault in the fixtures

The faucets and showers in your home are used daily. With time they start to wear and tear. Faulty fixtures are one of the most common reasons for low water pressure. Once they get old the fixtures easy clog up with limestone, dirt, and even rust. All of which results in lower water pressure.

The best way to test whether it is a certain fixture is to run water through it at the same time with another. If you notice a difference in the pressure of the two then you know that one is faulty. Before running the test, just be sure to clean the aerator of the fixture so no dirt is stuck in it, which also results in lower pressure. When you’ve determined a fixture to be faulty, you can clean it out to clearing out the clog or have it replaced.

Water pressure issue #3: A damaged pressure regulator

The pressure regulator does exactly as it names states, it regulates water pressure in the plumbing. It is important that the regulator stays in shape otherwise you will either get no pressure or too much of it.

Fixing a regular isn’t hard; you just need to replace it. You can do it on your own or seek help from an Appleton plumber.

Water pressure issue #4: Clog in the water pipes

If your fixtures and valve have been cleared after inspection then the reason behind low water pressure could be clogged pipes. Clogged pipes aren’t easy to deal with and is better if left to a professional. You can consult a plumber to help figure out how the clog can be resolved. This can only be done after they inspect the pipes and determine where the clog is.

Water pressure issue #5: Plumbing problem

Corrosion in the plumbing can happen in older homes. If you are having trouble diagnosing the problem then chances are the plumbing is corroded. This may require a complete overhaul of the plumbing, which is obviously a project you cannot take up on your own. An Appleton plumber can help you with the project they can assess the corrosion and determine what the proper step maybe.

Water pressure issue #6: Main supply line has issues

If your home has been cleared from the above issues then chances are there is an issue with the main supply line. The line doesn’t supply your home with enough water, which has resulted in lower pressure. A plumber in Appleton, WI can help you assess this problem and help you take the right step to have it resolved.

There are numerous different factors that cause water pressure to decrease The hard part for most homeowners may just be identifying what the problem is. Before you take any drastic steps on your own be sure to get an expert to help out with the assessment and tell you the right course of action to take. Otherwise, you may end up causing more problems.

Continue Reading

Tips For a Clean Garbage Disposal

November 15th, 2018

Tips For a Clean Garbage Disposal

Five Simple Tips For a Clean Garbage Disposal

The garbage disposal is one of the most underrated home appliances in the kitchen. Not only does it allow you to get rid of food scrap, but it also does so in an efficient manner. As helpful as it is, it can also become a headache if you don’t take proper care of it. Our drain experts at Tureks Plumbing Services has 5 tips for you that will help keep your garbage disposal clean.

1. Cleaning the disposal

Cleaning a garbage disposal is fairly easy, which is why it’s puzzling why people don’t do it. You don’t have to do it every day, even once a week will work. The best part is, it barely requires any effort or time. All you have to do is grab a few ice cubes from your freezer, drop them in the disposal, and turn it on. By a few, we don’t mean fill up the disposal with ice cubes but throw in around 6-7 cubes, more if your disposal is bigger. You want to leave the disposal on until you can no longer hear the ice grinding.

The ice works its charm in cleaning the disposal of grease left behind from the food. The ice congeals any grease present and then the disposal easily breaks it up.

2. Deodorizing the disposal

The disposal is constantly exposed to food scraps and what not. In due time it will start to smell, stinking up the sink area. You should deodorize immediately after cleaning it. Deodorizing is as easy as cleaning it. You can take either lemon or orange peels and slowly grind them in the disposal. If you would rather not use peels, you can also pour lemon juice in the disposal. This refreshes it with a citrus smell and also helps fight grease build up inside.

3. Unclog the disposal

There will come a time when you end up disposing of something that you shouldn’t have and the disposal clogs. Before you call in the professionals, you can save a few bucks and try to fix it on your own. You want to start off by unplugging the disposal. If you don’t know how to do that, just shut the breaker to the disposal off, you don’t want an accident by taking any risk with it.

Next, you need to grab a broom and put the handle side inside the disposal. You will find an impeller, push against it until the chamber turns. If you can dislodge the item or just reach in and grab it. If you have any trouble, don’t panic. You can call a Fox Valley plumbing company to come and unclog the disposal.

4. Fighting Tough Grease

If cleaning the disposal with ice cubes and lemon/orange peel isn’t enough to get rid of the grease then you can try flushing it with cold water. Most people make the assumption that hot water would work better, but it doesn’t. The cold water will solidify the grease making it easier to flush. Rather than flushing it down the pipe, which can mean it gets stuck in the pipe, you can flush it into a can and dispose of it.

5. Maintaining the disposal

One simple trick to maintain the disposal so it doesn’t grease or clog is to let the water run through it after you’ve used it. This ensures that no food particle or grease sticks around to cause any problems later on. Whatever you do, do not use any corrosive chemicals like drain cleaners in the disposal cause these cause more harm than good.

Maintaining and keeping your garbage disposal installation clean is important for it to function well. The methods listed in our tips barely take any time so you should easily be able to do it once a week. Otherwise, you may end up damaging it and having to pay quite a lot for repairs and proper cleaning from an expert.

Continue Reading

How to Keep Your Bathtub From Clogging

November 14th, 2018

How to keep your bathtub from clogging

Help! How Can I Prevent My Bathtub From Clogging?

You come home from a long day of work. All you’ve been thinking about on your drive back is getting into a nice, hot, steamy shower to help you relax. You step into the bathtub, rinse your body with water, lather the soap up and everything only to notice the water not going down the drain. What was supposed to be a relaxing shower turns into a nightmare.

Bathtub clogs can ruin the best of showers or bath. You don’t need to worry though; Tureks Plumbing Services has 4 tips that will help you keep your bathtub from clogging.

Drain covers were made for a reason

The drain cover is one of the simplest methods to help prevent drain clogs. It isn’t easy preventing hair from going down the drain as it usually falls while you shower. Hair is probably one of the biggest factors for bathtub clogs. A drain cover helps keep hair from going down the drain. It’s also an inexpensive solution since you can easily buy one at your local home store.

There are a wide variety of drain covers available, made from different materials. The most popular materials are stainless steel and silicone. After you get a cover, be sure to clean your drain cover once in a while because scum will build up.

Use a clog remover once every two months

Clog removers aren’t only helpful when you have a clogged bath or shower but can also prevent it from happening. It makes sure that the drain is free and breaks up any minor clogs that may be forming. Just purchase a reliable, top quality clog remover. Those that use too many corrosive ingredients may end up damaging your pipes in the long run.

If you are looking for a cheap drain solution then vinegar can help. White vinegar has chemicals in it that help break down build up. So you can pour around 15-20 oz. of it down the drain and let it work its magic for about 10 minutes. Then flush the vinegar along with the buildup with hot water.

Baking soda also gets the job done. It also doesn’t have a pungent smell like vinegar. Just grab a handful of baking soda and throw it down the drain. Get boiling hot water and pour it in after. This will clear the drain and eliminate any odor from it.

Let the water flow

A simple way to prevent clog is to let the water run for a few minutes after you are finished with your bath or shower. Just after you step out, turn the hot water on and let it flow through the drain for about a minute or two. The hot water helps flush any small build up in the pipes.

Avoid showering after putting on body oil

Grease is a known enemy of pipes. Grease easily sticks and causes clogged drains. A lot of people like to shower after putting body oil on this is a big no. It is better for you and the drain if you use the body oil after you shower and let your body soak it in rather than your drain pipes. If there is residue from the oil then that can easily be wiped off with a towel.

Maintaining a clean drain is important. If proper maintenance is not done then it can end you costing a lot. If you have tried the above tips but still have troubles with a clogged bathtub then it is time you give the professionals at Fox Valley Plumbing Company a call. They can help sort any drain issues you may have, leaving you with a free flowing bath.

Continue Reading

A Professional Bathroom Plumbing Service

October 17th, 2018

a professional bathroom plumbing service

What You’ll Get When You Invest In A Professional Bathroom Plumbing Service

To have a fully usable and sanitary bathroom, you need to have a functional plumbing system.  So, if your bathroom has a clogged toilet or drain, slow-draining tub, or low water pressure, all the activities taking place in this room will be affected or hampered.

Although it may be tempting to attempt a DIY job when it comes to repairing or maintaining your bathroom plumbing to save a few bucks, you have to know that all these tasks are best left to the experts.

Professional bathroom plumbing service providers understand the intricate details of bathroom plumbing and have the skills, knowledge, tools, and equipment to deal with any kind of issue that will cause this room to be unusable.

Hiring the Services of Turek’s Plumbing

Turek’s Plumbing, a trusted plumbing company in Wisconsin, offers a variety of bathroom repair and maintenance services that will ensure you and your family can use this room comfortably. These include:

  • Repair and unclogging of toilets
  • Improvement of low water pressure
  • Repair of leaking faucets
  • Repair of water and drain line leaks
  • Installation and repair of water heaters
  • Bathroom design and remodeling

Whether you hire the pros of Turek’s Plumbing for repair, maintenance, or installation, you will enjoy these benefits:

  • High-quality bathroom fixtures and piping equipment
  • Better comfort and hygiene
  • Improved electricity and water savings
  • Increased value of your home

Highly skilled and state licensed plumbing technicians

They are fully trained in using different plumbing detection and repair equipment and strategies. They also have full knowledge of all local and state codes. In addition, our plumbing technicians complete state-certified continuing education classes annually. They attend in-house weekly training classes as well to ensure they are up-to-date with all current, relevant codes and technical changes in the industry.

Friendly and professional staff

All our employees are accommodating and respectful. Additionally, we provide honest ethical service that will exceed your expectations at any time of the day or night. The company provides upfront and transparent pricing and warranties on labor and parts as well.

Expertise in providing customized services

Our plumbing technicians are trained to assess each situation carefully to produce the most effective results for your unique plumbing requirements.

Sufficient coverage

 Aside from being a state-registered and licensed company, Turek’s Plumbing is also fully insured. As such, all customers are protected in case any damage occurs while our technicians are working on your property.

When you hire a professional plumber in Appleton, WI to handle a simple or complex repair, installation, or maintenance work in your bathroom, you will always get your money’s worth. You will always have a better, fully functional bathroom when they complete their work.

Continue Reading

How to Install a New Water Heater

October 10th, 2018

How to install a new water heater

How to Install a New Water Heater

Today, instant hot water is no longer considered a luxury; it is now more of a necessity. When you have a water heater, you don’t have to run the bath for several minutes to get the right temperature. You won’t suddenly be drenched by cold water in the middle of enjoying a warm bath as well.

The key to enjoying a warm or hot water every time you need it is to install your water heater properly. Although this is a job best left to experts, there is nothing wrong with trying to install it yourself. And once you have any problems going through with any of the installation steps, you have to call a professional plumber immediately.

Installing Your Electric Water Heater

Below are the steps on how to install a new water heater properly and safely:

Turn off the water and electricity supply

Shut off the circuit breaker for the line where you will connect the heater.  Next, turn off the home’s main water shutoff valve or the shutoff valve at the cold water supply line running to your current heater.  

Drain the old tank

Turn off the cold water supply to the heater. This is often located at the top of the unit. Next, connect a hose to the water heater’s drain valve and open the valve. Place the end of the hose near a floor drain or into a pail.

Make sure you drain the tank completely before you turn off the valve and remove the hose.

Disconnect the electric and plumbing connections

Next, disconnect the water heater’s electrical wires. Label the wires or take a picture so that you can easily use them later when connecting your new heater’s wires. Once done, disconnect the hot and cold water supply pipes.

If your current heater used copper piping, you may need to cut the pipes. Use a pipe tubing cutter to do this and leave as much of the pipe as possible.

Remove the old heater and place the new one

Once you have taken down the old tank, place the new heater into position. Make sure you line it up with the existing electrical and plumbing connections.   

Next, install the different fittings. These include the temperature and pressure relief or TPR valve and discharge drain pipe. Make sure you follow the manufacturer’s installation instructions.

Connect the water pipes

If the cold water supply does not have a shutoff valve, now is the time to install one. When done, use the correct fittings to connect the cold water inlet and hot water outlet on the water heater to their respective pipes. Be sure to use the correct type of fittings.

Connect the heater to the electrical source

Use the previous wire connections as a guide and connect the new wires in the same way that you removed them. Make sure you follow the labels when connecting the cables to the electrical source.  

Set the temperature

Turn on the cold water supply valve to the water heater and turn on the main water supply valve to fill the tank with water. Next, restore power to the water heater circuit. Set the temperature between 110 and 125 degrees F and wait until the water in the tank comes up to temperature. Leave the water turned on for a few minutes to ensure that the heater maintains the desired temperature.

Getting Help from Pros

As you can see from the steps above, installing a new water heater is not an easy task. You will need a number of plumbing tools which you may not have as well.

If you don’t want your new water heater to become a fire, explosion, and health hazard, hire a pro to install it properly.

By hiring a plumber to handle the installation, you:

  • Ensure the electrical lines are connected properly and safely
  • Allow the ignition sources to be checked, cleaned, and repaired, if necessary
  • Avoid damaging the TPR
  • Avoid the possibility of bacterial contamination

By letting a trusted Appleton plumber handle the water heater installation, you will be sure you can use your newly installed electric water heater as soon as possible. You will be able to use it safely for a long time as well.

Continue Reading

6 Signs You May Have a Problem With Your Main Sewer Line

October 2nd, 2018

6 Signs You May Have a Problem With Your Main Sewer Line

Your property’s plumbing system goes beyond the visible pipes to the main sewer line connecting them. Today, plumbing problems are among the worst issues you would want to deal with as a homeowner because these may involve a hefty amount of your time and money. Often, this involves your main sewer line, resulting in busted pipes and flooded bathrooms.

But determining if the plumbing problem has something to do with your sewer line is not an easy task. Often, problems go unnoticed without professional help. A damaged main sewer line, for instance, is a huge problem that can become too expensive when not addressed immediately.
To help you, Turek’s Plumbing shares six signs you may have a problem with your main sewer line.

1. Nasty odors

A problem-free sewer line is airtight. So if you smell nasty odors coming out from the pipes, this means that there is a leakage in your main sewer line.

2. Sewage backup

Sewage backups are common. However, if this happens each time you flush the toilet, you may have a problem with your sewer line.
Remember that all drains rely on the main sewer line in order to drain properly. So if you notice blockages in your drains, this is a sure-fire sign of a damaged sewer line.

3. Slow Drains

One of the common plumbing issues homeowners encounter is a slow drain. Usually, this can easily be dealt with by drain cleaning or a plunger. But if these efforts don’t work anymore, the issue may already involve your main sewer line.

4. Sewage in your yard

Once your sewer line gets clogged, your home’s wastewater might not make it to the sewer. Instead, it gets out from the sewer clean-out, which then pours sewage into your yard.
A good indication that sewage is leaking out in your yard is when your lawn looks more lush than usual; that’s because sewage is an excellent fertilizer.

5. Mold

Mold is caused by several issues, including a damaged main sewer line. Even a small crack in the line will result in water leaks inside your home, leading to mold growth. Deal with mold immediately because this is detrimental to your health.

6. Foundation issues

Other signs of a damaged main sewer line include foundation issues like foundation settlement, cracks in the foundation slab, and sinkholes. These problems are often caused by leaks that are left unaddressed for a long period of time.
Plumbing problems can disrupt your daily routine. When dealing with these problems, a reputable Fox Valley plumbing company highly recommends calling plumbing experts, regardless of how mild or severe they are. This is the only way to make sure that the problem is fixed properly.

Don’t wait for your main sewer line to be damaged! The moment you notice a plumbing problem inside or outside your home, immediately call a professional Appleton plumber.

Continue Reading

When Should I Replace My Home Appliances?

September 26th, 2018

When should I replace my home appliances

When Should I Replace My Home Appliances?

Our home appliances allow us to cook, keep our food fresh, and do a lot of chores more efficiently and faster. They provide a lot of conveniences that without them, we will have a hard time functioning properly.  

Because of our reliance on various home appliances, we are so used to them being around that we tend to forget when we bought them, and even neglect to maintain and clean them properly.

However, if you are now asking yourself “When should I replace my home appliances?”, the first thing you have to do is to find out how old they are. If you kept the receipts, simply check the date. 

In case the appliances you have in your home were installed by the previous owner, look through the paperwork that you signed when you bought the house or try to find the original listing. The past owner may have written the age of all the major appliances on these documents. He or she might have also left behind the original paperwork for the appliances which will have the date of purchase and installation.

Pros from a Fox Valley plumbing company say if you can’t find any of these documents, look for the label on your appliances. The label will have the date when the appliance was manufactured. This may be an actual date with a month and year or the info is coded into the serial number.

Lifespan of Home Appliances

Once you know the date when the appliances were bought or manufactured, you need to know how long they can be functional and cost-efficient devices to have at home.

Tureks Plumbing shares below the average lifespans of the most common household appliances:

  • Refrigerator – 8 to 15 years
  • Stove – 10 to 15 years
  • Microwave oven – 5 to 10 years
  • Washing machines – 8 to 12 years
  • Dryer – 11 to 18 years
  • Dishwasher – 8 to 10 years
  • Garbage disposal – 10 to 15 years

Should You Replace or Repair Your Appliances?

If an appliance has already passed its minimum lifespan and it is still working properly, you can continue using it. Our friends at Gilmore Heating & Air, a residential ac company in Placerville, adds that regular maintenance can prolong its quality and usability. Stay on top of maintenance just like you do with your heating and cooling system.

However, if the appliance won’t turn on at all, it could mean it is beyond repair. So, it’s time for a replacement from an expert. Although the appliance may work after being repaired by a professional, you have to way out the pros and cons. If you are continuously having the appliance repaired at a high price, you might as well get a new one.  

A good rule of thumb to remember is that if the repair will cost over half of what a new appliance would cost, it is best to get a replacement. If you have any questions or concerns, be sure to contact us.

Continue Reading

Causes of Foul-Smelling Septic Tank and Slow Drain

September 12th, 2018

Causes of foul-smelling septic tank and slow drain

Foul-Smelling Septic Tank and Slow Drain: 4 Possible Causes

A foul-smelling septic tank and slow drain are among some of the serious plumbing problems that must be addressed immediately. Otherwise, these can lead to costly home repairs.

To better understand how these problems happen, Turek’s Plumbing shares four potential causes and some ways to prevent them.

Overuse

Just like any home appliance or furnishings, overusing your draining system can lead to problems. If, for instance, you and your family are using more water and giving out more waste than what your septic tank can accommodate, slow draining will happen in an instant.

Water usage is usually the main culprit because, with too much water, the septic tank will drain too long. Also, the sediments that have settled at the bottom of the tank will be disturbed. As a result, it will flow into the leach field, which will then clog up the system. When this happens, there will be sewage backup, and wastewater can leak into your home and in your yard.

Thus, if it has been 2-3 years since your septic tank has been pumped-out, contact an Appleton plumber now. A professional septic tank pumping and cleaning service will prevent the occurrence of serious septic tank problems. Investing in this service periodically will prevent blockages in the sewer drain, eliminate foul smells, and prevent the leakage of sewage.

Mechanical Issues

Slow drains can also be a result of mechanical issues. Your toilet or sink may have become ill-fitted over time. This must be checked by a Fox Valley plumbing company to make sure that your fixtures and drainage will once again function efficiently and properly.

Tree Roots

The roots of your trees are too resilient. They can easily drill right through anything that is on their way. So make sure that your drainage system and septic tank are installed in an area where tree roots can’t reach.

Long Plumbing Maintenance Intervals

Plumbing maintenance must be done on a regular basis. But if you have a busy daily schedule, there is a higher possibility that you’ll forget to call professionals to inspect and clean your septic system. You may only be reminded when it’s already too late.

So to prevent this from happening, you need to create a schedule or perhaps assign a family member to remind you of the cleaning and pumping schedule. If not, you can use today’s technology – for instance, create a reminder on your smartphone.

Adhering to a regular maintenance schedule for your septic system must be taken seriously. After all, this is the only way for you to enjoy a quick-draining home.

Continue Reading

Bathroom Plumbing Basics

September 5th, 2018

Basic plumbing problems

5 Bathroom Plumbing Basics Homeowners Should Know By Heart

Plumbing issues in the bathroom can be one of the most stressful problems you can have in your home.

Knowing the basic bathroom plumbing hacks can ensure you can still use your toilet until a professional plumber can get to the bottom of your issue and provide a long-lasting solution.

Here are five bathroom plumbing basics you should know about to deal with some common plumbing issues:

Low water pressure

Taking a bath with low water pressure can really be a drag. But before you call a plumber, check if the pressure remains low when you switch from cold water to hot water. If it does, this means that there is some kind of mineral deposit in your shower head aerator.

If your aerator is removable, take it out and soak it in vinegar overnight. In case the aerator is not detachable or your shower doesn’t have one, soak the shower head in a bag of vinegar overnight.

In case this quick-fix does not work, an Appleton plumber says that the shower head cartridge may be blocking the water flow, thus causing the low water pressure. For this instance, you need to call a plumber since the cartridge needs to be removed and fixed or replaced.

The plumber will also need to the check the water pressure at the water meter and inspect your pipes to determine other possible causes.

Leaking faucet

One of the most common causes of a dripping faucet is a worn-out washer. This is the rubber part that forms a seal to prevent water from coming out. All rubber washers wear out over time due to exposure to water.

To know if this is the cause of dripping faucet in your bathroom, you will have to unscrew the faucet to remove the cartridge and check the washer. If you don’t have the tools to unscrew the faucet and to remove the cartridge, you will have to call a plumber.  

Slow or clogged drains

Slow or clogged sinks and shower drains are often caused by a buildup of accumulated hair, soap and shampoo scum, and other debris in the drains.

To fix this issue, remove the pop-off drain cover in the sink or shower floor. Put on some rubber gloves and remove any debris. You can also use an auger or an old, partially straightened wire hanger to pull up hair strands and other debris.

If this does not fix the problem, use a plunger to loosen the debris. Next, flush the drains with a mixture of vinegar and baking soda to further unclog and clean the drains.

Clogged Toilet

A clogged toilet can make your bathroom and even your home unsanitary.

If you’re not afraid to get dirty to try and fix this problem, use a plunger to remove the clog. In case the plunger does not work, use an auger to dislodge clogs that the plunger can’t reach.

If you don’t want to unclog your toilet on your own or it still doesn’t work, call a professional.

Running Toilet

Lastly, a running toilet problem can often be fixed by replacing a warped or broken flapper, installing a new chain, or readjusting the float.

If you have this issue, you should start by checking the flapper valve first since this part often breaks easily. You can then replace the flapper easily. There are also different toilet repair kits you can buy to stop water from running continuously in your toilet.

In case any these quick fixes do not work, hire a plumber to check your toilet since there will be a deep-seated cause behind this problem.

When you have a bathroom plumbing issue, it is important that you know the difference between minor and major plumbing issues. This will help you save a lot of time and effort in attempting a DIY job. It will prevent you from spending more money than needed as well.

Continue Reading

Warning Signs of a Damaged Sewer Pipe

August 27th, 2018

Warning Signs of a Damaged Sewer Pipe

A damaged pipe can be a big hassle and a huge drain on your monthly budget.

And unknown to many homeowners, this issue often takes years to arise. More often than not, the warning signs of a damaged sewer pipe are there, hiding in plain sight, ignored, or attributed to another problem.

Homes that are 25 years old or older are particularly vulnerable to damaged sewer pipes. This is because these often use cast iron pipes.

What are the warning signs of damaged sewer pipe homeowners should be on the lookout for?

Slow drainage

Slow drainage is a fairly common plumbing problem which can be resolved fairly quickly. However, if the problem is not resolved after several attempts, it may be a sign of an impending sewer pipe damage.

Here, slow drainage is an indicator of the formation of the blockage.

Foul odor

A sewer pipe that is in good working condition should be able to contain the scent of sewer gas.

If you notice that distinct odor in your home, it may be a sign that the sewer pipe has been cracked.

Backups and blockages

When the backup or blockage occurs in more than one drain, it is highly likely that your sewer pipes are deteriorating.

Therefore, these types of backups and blockages do not respond positively to pipe cleanings.

Molds

Molds build up when the humidity level inside a home increases. And one of the possible causes for the increase of humidity inside a home is a cracked sewer pipe. Our friends at Gilmore Heating & Air, a residential ac company in Placerville, recommend consulting with an HVAC company to learn about bacteria-fighting heating and cooling systems.

Pest problems

You have tried practically every solution available for you to get rid of rodents and insects that have infested your home and nothing still works.

It’s not that the solutions that you have implemented are simply not working. It is highly possible that you are attacking parts of the problem.

These unwanted invaders take advantage of the smallest available space to invite themselves in your home.

Patches of unusually green grass

You’re proud of your lawn and all of the efforts you have put toward it. But during one of your mowing sessions, you notice one particular area where the grass seems to be thriving.

The culprit may be the sewage leaking below that area, blessing the grass with nutrients.

Structural damage

When sewer pipes are nearing the end of their usable lifespan and potential damage is imminent, you will notice structural damage in and around your home.

So, this can take various forms, including cracks or settlements in the foundation, sinkholes, and indentations in the lawn or beneath pavers.

Be vigilant

Taken individually, these signs may be considered as indicators of smaller problems.

But if you notice these in conjunction with one another, you might be facing a serious plumbing problem. Contact a plumbing expert immediately. 

Continue Reading