Tureks Plumbing Services Blog: Archive for the ‘Plumbing Trends’ Category

Causes of Leaking Garbage Disposal

Tuesday, July 25th, 2017

Fixing the 2 Most Common Causes of Leaking Garbage Disposal

A leaking garbage disposal system does not necessarily translate to a massive hole in your pocket. Leaks can occur from time to time and in some instances, you do not have to spend a small fortune to remedy these problems.

Here’s a brief rundown of two of the most common causes of leaks and what you can do about these.

Gasket

Check your garbage disposal system and determine where exactly the leak is coming from. If the leak is coming from the top rim where the rubber seal and the flange meet, it is highly likely that the cause of the leak is the gasket which can be found on top of the system.

Over time, the rubber gasket breaks down. In some cases, if the garbage disposal system is not used for an extended period of time, the gasket can dry up, causing leaks. Sometimes, the gasket causes leaks if it is replaced unevenly. Finally, if you dismantle the system for whatever reason, it is a good idea to replace the gasket.

Fortunately, if the gasket is the cause of the leak, it can be easily replaced. Just make sure that you purchase the right gasket for your garbage disposal system.

After you have bought the correct gasket, the first thing that you need to do to replace the old one is to disconnect the drain. After that, you can unplug the cord. Make sure that you remove the dishwasher drain hose from the system.

Next, hold the sides of the mounting nuts and turn these counter clockwise. This will unlock the garbage disposal system.

The next step that you need to do is to remove the old gasket and put the new one that you bought. Check whether the new gasket fits properly. After that, you can replace the garbage disposal system and reconnect the drains and plug.

Disposal flange

If the leak comes from the upper area of the garbage disposal system, the possible source of the leak is the disposal flange.

The flange can leak if the seal is not tight enough or has become loose. In either case, you will need to dismantle the system so that you can reseal the flange.

After dropping the garbage disposal unit, you will need to loosen the bolts that hold the flange in place. Next, find the clip that holds the flange in place by using a flat screwdriver to pop it out of place. Then, remove the top flange from the sink. You should then clean the sink before reinstalling the system and applying putty.

In applying plumber’s putty, make sure that you apply an even amount. You should also make sure that the putty wraps around the rim of the flange. After that, you can put the flange into its original position and replace the bottom flange. Replace the screws tightly and then you can clean the area where you worked. And schedule your appointment with us today!

Tags: affordable bathroom remodel, bathroom plumbing, Bathroom Plumbing Problems, bathroom remodel in Fox Valley, commercial plumbing, emergency plumber, kitchen plumbing
Posted in Bathroom Remodel, Commercial Plumbing, Kitchen Plumbing, Kitchen Remodel Planning, Plumbing Problems, Plumbing Trends, Remodel Contactor, Remodel Contractor, Residential Plumbing | Comments Off on Causes of Leaking Garbage Disposal

5 Things That Cause Drain Clogs

Thursday, July 20th, 2017

It is normal for debris to accumulate over time, but there are certain items that can make your drains clog faster. The following are five of the likeliest causes of drain clogs and what homeowners can do to reduce the chances of a blocked drain.

Hair

Clogs caused by hair strands are more common in bathroom sinks, showers and tub drains. Each time you shower, you lose hundreds of strands. These thin strands normally get washed away, but on a rare occasion, strands may get stuck along the walls of your drain pipe. Over time, the buildup can block the flow of water and clog your drain. Installing a hair catcher or sink guard helps, but won’t totally prevent clogs. It is possible to find clogged bathroom drains, especially in older homes.

Soap

Dirt, grime, hair strands, dead skin cells and other types of waste can stick to the soapy residue and cause a blockage. Other than bathroom sinks, showers and tubs, soap scum can also become a problem when washing dishes. One way to reduce this buildup is to pour two buckets filled with hot water and chlorine down the sink at least twice a month.

Grease

Grease buildups more commonly occur in kitchen sinks. Similar to the case of soap scum, small food particles and other sediments can get trapped in this thick, gooey liquid. However, unlike soap, the oily residue is more difficult to remove. You can try using cold water when running your garbage disposal. This can help remove some of the layers of grease and let the fat flow more freely through the drainage pipes.

One better way to prevent grease buildup is to avoid pouring any type of oil down the drain at all. Instead, what you can do is to pour the grease directly into the garbage. This prevents any residue or particles getting stuck along the pipe’s walls.

Toilet paper

Toilet paper sheets are designed to break down easily when exposed to water. This makes the sheets easier to flush. However, paper towels, baby wipes and multi-ply tissue paper are more durable and may not break down as easily as a single ply sheet of toilet paper. To prevent blockage, avoid flushing these types of toiletries down the toilet. Inform your relatives, friends or guests to do the same when staying at your home.

Napkins and diapers

Finally, these types of hygiene products are a major cause of concern. Because they are designed to absorb water, napkins, diapers and other similar products can quickly cause a blockage. Always throw these types of items straight into the trash and not into the toilet bowl. And make sure to call us today!

Tags: bathroom plumbing, commercial plumbing, emergency plumber
Posted in Commercial Plumbing, Kitchen Plumbing, Plumbing Problems, Plumbing Trends, Sewer and Drain | Comments Off on 5 Things That Cause Drain Clogs

Slow Drain Septic System Problems

Thursday, June 22nd, 2017

Slow Drain Septic System Problems: Signs, Causes, and How to Fix Them

The bathroom is one of the dirtiest places in your home since different types of bacteria can be found here. Once you have a drainage or septic system problem, you will consider your toilet even more unsanitary and a hassle to use.

Signs of a Septic System Issue

Septic system problems are more common in houses and buildings that have already been in use for many years. Some of the signs that indicate you already have this kind of plumbing problem are:

Water is draining slowly from the shower, bathtub, sink, and other areas
The sound of gurgling from the tub or sink when a toilet is flushed
Water backing up in toilets, tubs, and sinks
Water puddles on the grounds on your lawn
The smell of sewage odors outdoors

Possible Causes

There are several reasons why you have a problematic or slow drain septic system. The most common one is the overuse of the system. This means that too many people are using or too much water is being used in the household or building that the usage has gone beyond the system’s capacity.

Another common cause of this problem is the lack of or delay in inspection, maintenance, and pumping. Once your septic tank becomes full, the filter in the outlet baffle will start to plug. This plugging action will cause the water level inside the tank to rise which will restrict the flow of effluent.

Finally, your septic system may not be working properly if something is clogging the pipes or drains. Grease, food, certain sanitary products, toys, or even pieces of clothes can be stuck somewhere in the pipes and cause the slow drain or the system’s malfunction.

Getting Things Back to Normal

If the reason behind your slow drain problem is a blockage, you can remove the clog by using some tools at home. However, harder clogs and blockages will require the use of a plumbing snake; in such instances, it is best to call in experts to do the job to avoid further damaging your plumbing and septic system.

Calling in professional plumbers at the onset of a problem is always a smart idea since the contractors will know how and where to identify the issue quickly. In case you have slow draining fixtures, plumbers will check the drain-vent system. If the problem is in this area, they have the expertise, tools, and equipment to fix the issue. Also, if you already have a failed septic system, qualified plumbers will be able to detect this easily. Depending on the particular problem and design of your system, the professional plumbers will give you sound advice on whether it is best to have your system repaired or replaced.

Tags: bathroom plumbing, emergency plumber, Fox Valley Plumber, Plumbing Problems, sewer and drain, Slow Drains
Posted in Fox Valley Plumber, Plumbing Problems, Plumbing Trends, Sewer and Drain, Uncategorized | Comments Off on Slow Drain Septic System Problems

How to get jewelry out of a drain

Wednesday, May 31st, 2017

You are doing the dishes after a family meal and before you even finish, your prized piece of jewelry (a ring, bracelet, earring) slips off from you. Before you even have the time to catch it, it goes down the kitchen sink.

What should you do?

If you want to know how to get jewelry out of a drain, here are the steps that you need to follow.

Keep the area off limits

Tell the members of the household to avoid using the sink until the item has been retrieved. Otherwise, it will become increasingly difficult to get the jewelry back.

Turn off the garbage disposal and water

If water keeps on flowing down the drain, the jewelry might be pushed down further until it reaches the sewer line. When that happens, the chance of getting the item back becomes slim.

Stopping the flow of water increases the likelihood that the item goes to a more accessible area of the kitchen plumbing system, like the P-trap.

Find a magnet

Find a strong magnet and attach it to a string. After that, lower the magnet down the drain. There’s a good chance that you can get your jewelry back with this nifty trick.

Check the P-trap

If you can’t retrieve your jewelry with a magnet tied to a string, the next best thing to do is to check if the item is sitting inside the P-trap.

Before removing the different components of the P-trap, you should place a bucket underneath it to catch the water, the grime, and hopefully, the jewelry that went down the drain.

Start by removing the slip nuts and the J-shaped part of the P-trap using either a pair of pliers or a wrench. If you are lucky enough, you will be able to retrieve the lost item and you can replace the parts that you remove. But before replacing these parts, it is a good idea to clean the gunk off the pipes.

Call your Appleton Plumber

If you are unable to successfully retrieve the item or if you do not want to gamble and test your luck with your home’s plumbing system, consider calling in the experts for help.

Preventing this plumbing emergency

If you wish to avoid the loss of a piece of prized jewelry, there are a few things that you can do.

As much as possible, remove any jewelry before doing the dishes, especially if the sink is open and unstopped.

Place the jewelry that you removed from yourself in a safe area and not over the sink. Alternatively, you can put a jewelry tray nearby.

Put drain stoppers in the kitchen and bathroom sinks. These can help prevent jewelry and other valuable items from going down the drain.

If you have a piece of jewelry trapped in your drain, please call us today for help!

Tags: affordable bathroom remodel, bathroom plumbing, Bathroom Plumbing Problems, bathroom remodel, bathroom remodel in Fox Valley, Clogged Toilets, commercial plumbing, Facts About Plumbing, Fox Valley Plumbing Company
Posted in Bathroom Remodel, Breaking News, Commercial Plumbing, Emergency Plumber, Fox Valley Plumber, Plumbing Problems, Plumbing Trends, Residential Plumbing, Sewer and Drain | Comments Off on How to get jewelry out of a drain

Why Are My Drains Bubbling?

Tuesday, May 23rd, 2017

Bubbling toilets or drains explained

Whenever you use the bathroom to take care of your personal hygiene, the only sounds you would want to hear are the ones you make as you move around — the sudden rush of water as you turn on the tap, the toilet flushing, water going down the drain. If your body pipes up as well — such as your stomach rumbling thanks to the heavy meal you had earlier — that would be expected, and thus totally fine, too.

What you don’t want to hear, however, is a gurgling noise coming from various areas of the bathroom. If you hear this gurgling or bubbling noise after you use the shower, sink, or the toilet, it could mean trouble — and it’s something that you shouldn’t ignore.

Why are my drains bubbling? Here are possible answers to this question:

· There is a blockage in your vent pipe or drain

· A pipe may have collapsed or gotten damaged

· There is a buildup of grease dirt or other debris in your home’s plumbing

Vent pipes are joined to the major pipes that make up your home’s plumbing. These typically end at the roof of your house. If a vent pipe is blocked by things such as accumulated dirt or debris coming from outside your house such as dead leaves, these gurgling noises indicate that air cannot escape through the vent. Instead, the air makes its way to the nearest available opening, which could be the sink in your bathroom.

If the problem is buildup in your plumbing, it means that water cannot drain properly. Typically, both water and air flow through the drain and then escape the pipes through their respective spots. When the pipes are dirty and blocked, however, the air bubbles will end up getting expelled at the nearest vent, which results in the bubbling noise.

Keep in mind, though, that if you hear the gurgling noise in every drain you can find throughout the house, then it is an indication of a much bigger blockage in the main plumbing pipe, and not in the smaller pipes attached to the drains.

How can these blocks — and consequently, the gurgling sounds — be prevented?

There are a number of things that everyone in the household can do to keep your home’s pipes free and clear:

· Refrain from pouring or throwing anything down the drain that could cause buildup — this could be grease, hair strands, food particles, and other physical waste.

· If the buildup already exists, you can try using chemical solutions to clean out the pipes. Make sure to use the product as directed so that they can work as intended. Also, remember to follow safety precautions when handling the chemicals.

· Alternatively, an auger can be used to manually unclog the pipes. With sufficient force, any buildup can be broken up, but take care not to cause damage to the pipes and cause additional leaking problems.

If you’re unsure about how to perform these properly, there’s always the option of getting in touch with the plumbing specialists in your area. These professionals will know exactly how to diagnose and resolve your plumbing problems and get rid of that troublesome gurgling noise once and for all.

Tags: bathroom plumbing, Bathroom Plumbing Problems, Bathroom renovation, Clogged Toilets, commercial plumbing, Facts About Plumbing, kitchen plumbing, Plumbing Problems
Posted in Bathroom Remodel, Commercial Plumbing, Emergency Plumber, Fox Valley Plumber, Plumbing Problems, Plumbing Trends, Sewer and Drain, Uncategorized | Comments Off on Why Are My Drains Bubbling?

A Guide to Locating Leaky Pipes

Thursday, May 18th, 2017

Appleton Plumber Provides Advice in Locating Leaky Pipes

Isn’t it just annoying when you find a puddle in your house and you’re not sure what or who created it? Before you conduct your sleuthing, tough, you better wipe it up first lest somebody slips on it.If water no longer reappears after wiping up the area, it’s quite likely that somebody just spilled something on the floor. However, if a new puddle forms, one of the possible causes is a leaky pipe.

If you suspect that you indeed have leaky pipes, the plumbers trusted by Fox Valley and Applegate residents have an easy guide, provided below, that you can follow to locate where the leaks are.

How to take care of the problem

Wipe up the puddle again and then place paper towels or bags around the area where you found the puddle. The leak may be coming from under the floor or from the pipes located on the walls or overhead. If a drip falls, it will surely leave a spot and it’s going to be easy finding where the drip came from.
Do check supply lines or water-using appliances around the area as well. They may have rips or splits, or hoses that have come loose. Turn on the water to see if there are leaks anywhere and then turn the supply off once you see a puddle forming somewhere. It helps to perform this task to establish whether your damaged plumbing system or something else causes the puddle.
Once you identify where the leak is coming from, see if you can perform a remedial job that can control the leak until you can get a plumber to carry out a proper repair.
Now, if you no longer see a puddle after wiping it up, this doesn’t mean that there’s no leak. Observe the area for the next few days because it may just be a slow leak and it only creates a puddle when certain activities at home increase water pressure. You also need to take care of slow leaks because over time, they may get worse. Have your plumber have a look at them so preventive work can be carried out.

If you simply cannot find where the accumulation of water is coming from, set an appointment with your plumber right away. Leaks are no light issues; they can be the cause of accidents, they can attract moisture-loving pests (cockroaches, moths, spiders, and rodents), they can encourage the proliferation of harmful bacteria and molds, they can cause damage to other structural elements of your house or to your furniture, and they can create a spike in your water bill. Contact one of our Appleton, WI plumbers today!

Tags: bathroom plumbing, Bathroom Plumbing Problems, bathroom remodel in Fox Valley, commercial plumbing, plumbing in fox valley, sewer and drain
Posted in Bathroom Remodel, Commercial Plumbing, Fox Valley Plumber, Kitchen Plumbing, Kitchen Remodel Planning, Plumbing Problems, Plumbing Trends, Residential Plumbing, Sewer and Drain | Comments Off on A Guide to Locating Leaky Pipes

Signs My Water Pump Is Failing

Monday, May 15th, 2017

What Are the Signs My Water Pump Is Failing?

If you draw water from a well, most of the hard work of bringing water to your home is done by the water pump. However, if you come home with little to no water coming out of the faucet, one possible cause is a failing or broken water pump.

You’re probably wondering, “What are the signs that my water pump is failing?”

No water comes out of the faucet

If no water is coming out of the faucet when you turn it on, the first thing that you need to check are the pipes. Sometimes, the pipes may simply be clogged or broken.

However, if the pipes look like they are in good working order and are neither clogged nor broken, you can turn your attention to your water pump.

Loud and/or odd noises from the water tank

If you keep hearing loud and/or odd noises coming from your water pump, it is highly likely that it is about to fail anytime soon.

An increase in your electric bill

Take a look at your electric consumption over the past few months. If you think that your consumption has not changed but your bill has risen steadily over the past few weeks or months, the culprit may be your water pump.

Low water pressure

Again, you need to rule out other potential causes of low water pressure. Start by checking the condition of the pipes. Sometimes, repairing or changing broken pipes will restore normal water pressure. However, if the problem still persists, your water pump may be the main reason.

Maintaining your water pump

The price of a new water pump for your well can cost you a small fortune. Fortunately, there are a few things that you can do to get the most out of your investment.

Like other systems in your home, your water pump requires regular maintenance. Follow the manufacturer’s recommendations (including the schedule for maintenance) and have professionals inspect it at least once a year.

Consider a submersible well pump

If you have an above-ground water pump, an experienced contractor can fix it for you. However, fixing a submersible water pump will be more of a challenge because it needs to be pulled from the well.

The advantage of submersible well pumps is that these can last up to 25 years. However, this lifespan can be affected by factors like the amount of sediment and other particles in the well. Contact one of our plumbers today!

Tags: Bathroom Plumbing Problems, bathroom remodel in Fox Valley, Clogged Toilets, emergency plumber, Fox Valley Plumber, sewer and drain, Tankless Water Heater, water heater, water heater repair
Posted in Fox Valley Plumber, Plumbing Problems, Plumbing Trends, Remodel Contactor, Residential Plumbing, Sewer and Drain, Water Efficiency, Water Heater, Water Heater Instillation, Water Heater Repair, Water Pressure | Comments Off on Signs My Water Pump Is Failing

Common Plumbing Problems In Older Homes

Thursday, April 27th, 2017

Even in today’s digital age, many people are still looking to buy older homes. But often, these buyers are only looking at the surface of the house.

It’s important to look beyond what you can easily see — for instance, check the pipes.

Galvanized Pipes

Plenty of older homes have galvanized piping. A galvanized pipe is made of steel covered with a layer of zinc to protect it. But the zinc erodes from the piping over time, which causes the pipes to fail from the inside. In turn, this leads to different problems like stopped-up toilets and faucets and low water pressure. Sediment will fill the pipes as they corrode, thereby blocking water flow.

Concrete or Cast Iron Pipes

Some older homes have these kinds of pipes. Concrete pipes won’t deteriorate; however, they will shift and move under the home’s foundation. Cast iron pipes, on the other hand, will deteriorate over time just like the galvanized pipes but can eventually disappear.

Lead Pipes

These pipes have a lifespan of a century. Although they wear well, they may leak lead into the drinking water, causing serious health conditions to households.

Copper Pipes

These can be too pricey for home plumbing, but copper pipes are reliable and durable since they are not prone to leaking.

What else to look for?

Thoroughly check the components attached to pipes, water heaters, drains, and other plumbing systems regularly. When they are not maintained properly, huge problems can happen.

A valve on a line might look normal but it may not work well. Just because it is not leaking does not necessarily mean that there’s no problem with it.

How to Manage Plumbing Issues in Older Homes

Determine what kind of pipes were installed – Whether the property has copper, galvanized or concrete pipes, let a licensed plumber inspect it. This professional knows if the pipes are still fully functional or already need replacement.
Have a professional check the foundation of the property – Aside from the deteriorating pipes, it is also possible that tree roots have strangled the property’s sewer lines. To prevent costly future repairs, ask a certified professional to check the foundation of the sewer lines and septic systems of the property.
Renovate – This is the last resort in managing plumbing issues in older homes. Replace the older pipes with new plumbing systems. Also, replace or repair the property’s water lines, drains, vents, and sewer lines.

Prior to buying a house, it’s always best to know and understand the common plumbing problems in older homes. Also, you should have a professional plumber evaluate the property’s current plumbing condition – which is why you should call us today!

Tags: bathroom plumbing, Bathroom Plumbing Problems, bathroom remodel, bathroom remodel in Fox Valley, commercial plumbing, Facts About Plumbing, kitchen plumbing, Plumbing Problems
Posted in Bathroom Remodel, Commercial Plumbing, Fox Valley Plumber, Kitchen Plumbing, Kitchen Remodel Planning, Plumbing Problems, Plumbing Trends, Sewer and Drain, Uncategorized, Water Efficiency, Water Heater, Water Heater Instillation, Water Heater Repair, Water Pressure | Comments Off on Common Plumbing Problems In Older Homes

Things To Know When Installing A Tankless Water Heater

Tuesday, April 25th, 2017

Also known as a “demand type” water heater, a tankless water heater provides hot water only when needed. As such, it does not produce standby energy losses, which saves you money.

How a Tankless Water Heater Works

Water is being heated without the use of a storage tank. Cold water will travel from a pipe to the unit if a hot water tap is turned on. This means a tankless water heater delivers a steady supply of hot water. In other words, you do not have to wait for the storage tank to be filled up with enough hot water each time you need to use it.

Why Opt for a Tankless Water Heater?

Heating costs will be reduced – Enjoy monthly savings of up to 40% off your utility bill for the product’s life. Heating and reheating water in the storage tank is not required.
Only a small amount of space is needed – As compared to traditional water heaters, tankless water heaters will take up less space since this is just about the size of a small suitcase or even smaller.
Eco-friendly – Tankless water heaters are 30% more energy-efficient than tank water heaters. Maximum energy efficiency will help conserve natural resources.
Long-lasting – It has a longer lifespan for up to twice as much as that of the traditional water heater. This further means less waste in the landfill.
Clean – Avoid using water stored in a tank with accumulated rust.
Safe – A tankless water heater is equipped with excellent safety features to prevent injuries and burns caused by boiling water.

Installing and Maintaining Demand-Type Water Heater

Proper installation will greatly depend on different factors. These include the following:

Local building code requirements
Climate
Fuel type
Safety issues

Regular water heater maintenance is also important to extend the life of the water heater. This will also decrease loss of efficiency.

Proper installation and maintenance are very crucial to optimize the water heater’s energy efficiency. Therefore, it is best to have a licensed, skilled plumbing and heating contractor to install your tankless water heater.

Tips for Choosing the Right Contractor

Ask for references. Satisfied customers will give you peace of mind.
Request cost estimates from different contractors. Make sure that these estimates are for completed work and not just for sections of the system.
Check if they can get a local permit when necessary.
Determine if they fully understand local building codes.
Check if the plumbing contractor company is a member of the Better Business Bureau.
Sign the contract only after you’ve read and understood it.

If you’re looking to install a tankless water heater, please call us today!

Tags: affordable bathroom remodel, bathroom remodel in Fox Valley, Fox Valley Plumber, kitchen remodel, Kitchen Remodel Planning, Tankless Water Heater, water heater, water heater repair
Posted in Bathroom Remodel, Commercial Plumbing, Fox Valley Plumber, Kitchen Plumbing, Kitchen Remodel Planning, Plumbing Problems, Plumbing Trends, Remodel Contractor, Residential Plumbing, Uncategorized, Water Efficiency, Water Heater, Water Heater Instillation, Water Heater Repair, Water Pressure | Comments Off on Things To Know When Installing A Tankless Water Heater

How To Deal With Water Pressure Issues

Tuesday, April 18th, 2017

Low water pressure is the reduction in the pressure of the water that causes it to fail to reach the top level of the house. It is one of the water pressure issues that homeowners wouldn’t want to experience and deal with.

Identifying the root cause will greatly help in managing the problem. If you don’t determine and fix the main cause, it is highly possible that you will experience the same issue over again. If worse comes to worst, recurrent low water pressure could result in structural damage to the home.

Causes of low water pressure problems

Damaged or defective water pressure regulator. This bell-shaped device is preset by manufacturers and often does not need adjusting. But like any device, it gets old and malfunctions.
Water or plumbing leaks. Any damage to your home’s plumbing system may cause leaks or water to escape. This results in a decrease in the pressure of water.
Debris buildup inside the pipes. Dirt, sand and other debris may enter your plumbing system, which then causes a buildup and blockage in the pipes.
Corrosion buildup in pipes. Water causes steel or galvanized piping to corrode. Over time, the corrosion causes sediments to deposit and block passageways.

Dealing with low water pressure

Check the water pressure in your entire house. Check the bathroom, kitchen, basement, and outdoor faucets to identify if the issue appears in one area only or if the entire house is affected.

If you are experiencing low water pressure in a specific area only, such as the sink faucet in the kitchen or the shower in the bathroom, it is highly possible that the aerator, valve, or pipe is clogged. Take off the aerator or valve and clean or replace it.

Check for leaks and repair leaking pipes. To detect cracks of damages to pipes that cause leaking, shut off the water valve in your house and check the meter. Come back after some time and check the meter again; if there is an increase in the meter reading, then there is a leak. Minor leaks can be repaired using DIY techniques, but major leaks require the attention of professionals.

Check for a malfunctioning water pressure regulator. A problematic pressure regulator needs fixing or replacing. If you are not well-versed in fixing or hooking up a pressure regulator, it is best to leave it to certified plumbers.

If corrosion buildup is identified to be the cause of the problem, pipe restoration or pipe replacement should be done.

If you’re in need of help with water pressure issues, contact us today!

Tags: affordable bathroom remodel, bathroom remodel, bathroom remodel in Fox Valley, emergency plumber, Facts About Plumbing, residential plumbing, water heater, water heater repair
Posted in Commercial Plumbing, Emergency Plumber, Fox Valley Plumber, Kitchen Plumbing, Plumbing Problems, Plumbing Trends, Remodel Contactor, Uncategorized | Comments Off on How To Deal With Water Pressure Issues