Tureks Plumbing Services Blog: Archive for the ‘Plumbing Problems’ Category

Do I Need to Fix My Gurgling Drains?

Wednesday, September 4th, 2019

do i need to fix my gurgling drainsYou should be concerned if one or more drains in your home are emitting a gurgling sound each time that drain or another one is used. While the sound can be annoying, it is actually a good thing because it draws your attention to a developing problem. Read on and discover why drains gurgle and what you can do to fix the problem on your own before calling the experts at Tureks Plumbing Services for help.

Where Does the Gurgling Come From?

One of the most important steps, before you can fix the gurgling sound in your plumbing, is finding out where the sound is coming from. You can get answers to this question by listening carefully as you use different drains. From this observation, Fox Valley plumbers recommend that you note down the specific drain or drains exhibiting this symptom.

When Does the Gurgling Occur?

Tureks Plumbing Services also recommends that you take note of when gurgling sounds are emitted. For example, one drain may gurgle each time it is used. It is also possible for a drain to gurgle when another plumbing fixture is used. A clear example of this is when you hear gurgling in the floor drain of your bathroom when you pour water down the kitchen sink drain.

What Gurgling from One Drain Means

When you talk to an Appleton plumber about the gurgling from just one drain, he or she will immediately suspect that there is either a partial clog or blockage in that drain, or there is a malfunction in the vent of that plumbing fixture, such as the kitchen sink.

Solutions to Gurgling in One Drain

First, use a plunger to try and dislodge the clog that is blocking the single drain emitting the gurgling sound. If you try to use the drain and the problem persists, then it may be time to switch to an auger. Be careful when using the auger because any mistake that you make can result in damage to the plumbing pipe.

If you aren’t certain of your ability to accomplish this task on your own, contact a plumber in Appleton, WI for help in using an auger to safely get rid of the clog.

The second alternative solution is suitable for gurgling due to defective venting. Here, what is required is to clean the p-trap of the fixture from which the gurgling sound is originating. Access the vent and clean it so that it can start letting air into the drain as water is flowing through.

If you find that the plumbing fixture doesn’t have a vent, now is the time to call a Fox Valley plumber and ask him or her to install a vent on this particular fixture and others without vents.

What Gurgling from Multiple Drains Means

You can hear gurgling sounds from several vents in your home if the main vent of the plumbing system has a problem, such as a bird’s nest blocking it or when it is constricted by a heavy object. Alternatively, gurgling from multiple vents may also result if the main sewer line has a clog or is damaged.

Solutions to Gurgling in Multiple Drains

You may have noticed that your home has a vertical pipe that runs to the roof of the house. This pipe is the main vent of the entire plumbing system. Tureks Plumbing Services explains that once this vent is clogged, then air will be unable to enter the plumbing pipes and several drains will begin gurgling.

The fix to this problem is to access the vent on the roof and remove any clog inside that vent. You can use a thin piece of tubing to push down any debris which has entered the vent. This may also be the time to put an elevated cover or mesh on the vent opening so that tree leaves and other forms of debris don’t enter the vent in future. You might want to hire a Fox Valley plumber to perform this task if you are afraid of heights or you find climbing onto the roof too risky.

The second solution involves unclogging the main sewer pipe if the main vent has no problem but you continue to hear gurgling from different drains. If you are up to the task and you have the necessary tools, such as a plumbing snake, you can open the nearest cleanout port and push the snake into the pipe until you dislodge the clog.

Calling Professional Fox Valley Plumber

However, you are better off asking a plumber in Appleton, WI to clear the pipe. This professional will inspect the pipe using a camera and identify the kind of blockage hindering the flow of wastewater. For example, tree roots may have penetrated the pipe and partially blocked it. This inspection will enable the plumber to use the most appropriate technique to get rid of the clog so that the gurgling sounds are brought to an end.

It is vital that you resist the temptation to ignore the gurgling sound coming from a drain or several drains in your home. Any delay to address the problem can allow the situation to deteriorate and a plumbing emergency, such as a burst sewer pipe, can arise. Don’t let matters get this far. Call Tureks Plumbing Services as soon as you notice gurgling in any drain and our expert plumbers will assess and resolve the situation.

Continue Reading

Do Home Warranties Cover Sewer Line Replacement?

Wednesday, August 28th, 2019

home warranties cover sewer line replacement - Tureks Plumbing ServicesHome insurance policies usually have some significant gaps when you consider your sewer line. If that sewer line ever develops a problem, you may find yourself responsible for meeting the entire cost of the repair or replacement if you hadn’t secured insurance for this system. In this article, you will discover what you need to know as you shop for coverage for this expensive component of your home.

When It’s Worthwhile to Get Sewer Line Coverage

Tureks Plumbing Services recommends that you consider the age of your home as you decide whether to get sewer line insurance cover or not. The older the house is, the higher the risk that the sewer line will develop costly problems.

For example, homes built in the 1950s have sewer lines made from either cast iron, Orangeburg, or clay. Appleton plumbers explain that Orangeburg is the most likely to develop problems because this fibrous material is porous.

It is therefore wise to get sewer line insurance if your home is old and the sewer pipe materials are nearing the end of their service life. However, Fox Valley plumbers caution that any home, regardless of its age, is susceptible to sewer line damage. For example, the sewer line could be damaged after a bout of heavy rain that causes the soil to shift beneath the pipe. All homeowners should, therefore, consider acquiring sewer line insurance, which is customized to their specific needs.

Factors to Consider When Selecting a Sewer Line Insurance Provider

The Monthly Cost

An experienced plumber in Appleton, WI advises that homeowners should avoid acquiring sewer line insurance whose monthly cost is in excess of $20. This is because those costlier policies are harder to rationalize economically in the long-term.

For example, estimates put the average cost of sewer line repairs at $2,500 if the work involves digging up the yard. If the monthly payment is $20, then your annual fee will be $240. This translates into $2,400 in a decade. The chances are high that you may not have more than two issues in a decade that require sewer line repairs in excess of $2,500. You can see from these figures how it makes financial sense to get coverage costing less than $20 a month and how hard it gets to justify that expenditure if the monthly cost is higher.

The Deductible

A deductible refers to the out of the pocket amount of money that you are required to pay before insurance steps in when sewer line repair or replacement is done on your property. Policies with high deductibles are not advisable because the savings that you make on your monthly payments get eroded when repairs are needed.

If you can, find an insurer with a low or zero deductible so that you limit what you spend in the event that your sewer line needs to be replaced or repaired during the coverage period.

The Coverage Amount

Read the policy carefully and find out the value of the coverage offered with that policy. The larger the coverage amount, the safer you are from having to dip into your pocket when sewer line repairs come up.

Avoid the temptation of opting for bargain coverage which only covers repair costs that don’t exceed a few thousand dollars because you will have no choice but to meet the extra cost if a major repair is required.

The Limit Per Call

Read the fine print of the policy carefully regarding the amount of money mentioned in the annual coverage. For example, one policy may mention that it provides $5,000 coverage each year, but that policy limits each service call to a maximum of $2,500.

Such a policy is as good as saying that you are covered up to $2,500 each year because it is very rare that your sewer lines will suffer two major defects within one year so that you file two claims with your insurer.

To be safe, talk to a plumber in Appleton, WI about the average cost of having to conduct major repairs on your sewer line. This estimate will give you a ballpark number that you can have in mind when picking an insurer with a suitable cost limit for each service call.

Sewer Line Insurance Options

Now that you have established what you should look for when buying sewer line insurance cover, let us now turn to where or what form such insurance can take. The following are some of the options you can explore.

A Rider on Your Home Insurance

As already mentioned, your home warranty will rarely cover sewer line repairs or replacement. This is because the sewer system is looked at as separate from the main home, so it is excluded in the coverage for the home. However, you can acquire a rider to that policy so that the sewer line is also covered.

A Standalone Sewer Line Policy

If you assess the rider being offered by your home insurance cover and it falls short on the desirable attributes discussed earlier, you may have to consider shopping for a separate provider for this needed warranty. Some insurers specialize in this kind of cover, while others have it as part of a range of insurance services that they offer. Explore all the options available and select the one which will address your specific needs.

Sewer Line Cover Through the Utility Company

Another option that you could look into is the possibility of getting sewer line coverage through the utility company in your area. Fox Valley plumbers report that it is becoming increasingly common for municipal authorities to partner with insurance providers to enable homeowners to get insurance for their sewer and water lines. The biggest benefit of getting such a policy is that you will pay the monthly premium with your water bill, so you will have less paperwork to deal with.

All insurance policies are unique, so it is imperative that you do your homework sufficiently before you put pen to paper. If you still have questions, talk to your insurance broker for professional advice. Needless to say, contact Tureks Plumbing Services if the sewer line or any component of the plumbing system develops a problem and you want the problem fixed professionally and affordably.

Continue Reading

How to Locate Your Sewer Cleanout

Wednesday, August 21st, 2019

sewer cleanout - Tureks Plumbing ServicesThe sewer lines on your property are important pieces of infrastructure because they move wastes and water away from your home. It is therefore essential for you to maintain this system so that it gives you years of trouble-free service. One of the crucial things you should know is the location of the sewer cleanout valve from where you can remove any debris and waste which could clog the system. The experts at Tureks Plumbing Services recommend that you use the following measures to locate this crucial component of the sewer system.

Refer to the Engineering Plans of Your Lot

The cleanout port is an above-ground vertical pipe that drops to the main sewer line on your property. Fox Valley plumbers explain that this vertical pipe usually has a plug at its top to prevent debris from falling into the main sewer line. When an Appleton plumber wants to unclog the sewer line, he or she will most likely start by opening the cleanout and pushing a plumbing snake into the sewer pipe. If you cannot tell the plumber where to find this pipe, then you could pay more as the plumber spends time to search for this fitting.

The first step that Appleton plumbers recommend that you take in your quest for the location of the cleanout access port is by examining the engineering drawings of your home. These documents will point out the different components of the plumbing system, including the location of the cleanout port. Follow the directions given in the plans, and you will find the cleanout port long before the need to use this fixture arises.

Check the Likely Places

Not every homeowner has access to the engineering drawings of the property, especially if it is an older home. In that case, don’t give up on finding the location of the cleanout port. Instead, start your search from the most likely places where this component could be located.

For example, plumbers in Appleton, WI, suggest that you go outside your home to the side where the bathroom is located. Once there, start your search as you move away from the foundation towards the street. You are likely to see this pipe projecting out of the ground.

Plumbers from Tureks Plumbing Services have also seen several homes where the cleanout port is either located in the basement of the house, or it is hidden behind drywall. This is especially likely in homes that are found in cold areas since putting the cleanout indoors prevents it from freezing up during cold weather. Check these places as well and be careful while cutting bits of drywall to avoid damaging electrical wires installed within the walls.

Get Professional Help

If you cannot locate the cleanout after reading the engineering drawings of the home or by searching the places where cleanouts are usually located, it is time to ask Tureks Plumbing Services for help. Our trained professionals have the knowledge and experience to find the cleanout in a short time without tearing up large sections of the drywall or other components of the home during the search.

Once we locate the cleanout, we will use the most appropriate tools to open it and clean it so that the sewer system can function optimally again. So, why bother with this unpleasant task when you can leave it in the capable hands of our professionals? Give us a call today!

Continue Reading

How to Unclog Your Shower Drain

Thursday, April 25th, 2019

how to unclog your shower drainHow to Unclog Your Shower Drain

Usually, the shower drain will start to gradually clog up. One of the first signs you may notice regarding this problem is when water starts reaching ankle-deep while you take a shower. When this happens, you may be at a loss regarding which method you should use to fix the problem. Follow the tips suggested below by the experts at Tureks Plumbing Services to learn how to unclog your shower drain.

Assemble Your Tools

Before you start, you need to gather and assemble everything that you need to complete this task. The tools you are likely to require may include screwdrivers, a straightened coat hanger or a drain claw. You may also need white vinegar, baking powder, latex gloves, and a plastic garbage bag. This plastic garbage bag will be a receptacle for the debris you retrieve from the drain. Place all these items in a bucket so that they are within easy reach while you work.

An experienced plumber in Appleton, WI also recommends that you get a plumber’s snake, a toilet plunger, a chemical drain cleaner, and pliers. Add these to your collection of tools and you should be well on your way to a clean shower drain.

Snoop Around

Get a screwdriver and use it to remove the drain strainer cover. Next, take the flashlight and shine it into the drain. Peek inside and find out whether you can see the clog blocking the shower drain. If you can see it, put on the latex gloves and use a drain claw to pull the clog out of the drain. If you don’t have a drain claw, then a straightened coat hanger with a hook made using a pair of pliers will suffice for this task.

Once the visible clog is out, run some hot water and observe whether the drain is working properly.

Time for Some Pressure

If the water is still draining slowly, a Fox Valley plumber suggests that it may be time for you to switch to the next strategy in your fight against the clog. This other measure entails using a plunger to apply some pressure within the drain pipe so that the clog can hopefully be dislodged.

Apply some petroleum jelly on the rim of the plunger so that it can form a tighter seal on the drain opening. Pump the plunger multiple times for several minutes so that pressure accumulates and pushes the clog down the drain. Run some hot water and see if the water drains swiftly.

Snake It Out

If the plunger doesn’t produce the desired outcome, switch to using a manual plumber’s snake to break up the clog. Experts at Tureks Plumbing Services suggest that you first push the snake gently into the drain until it stops moving. That is your cue that the clog has been reached. At this point, crank the handle so that the head of the plumbing snake can cut through the clog and force the fragments to move down the drain.

Once again, run hot water through the drain. Repeat using the plumber’s snake if the water is still draining slowly.

Plan a Natural Attack

You can also use natural ways to unclog your blocked shower drain. One of the best natural remedies involves the use of hot water, baking soda and vinegar. For this approach, you first pour boiling water down the drain and then pour a cup of baking soda and another of vinegar into the drain.

This mixture will react with the clog and break it up into smaller pieces. Flush more hot water down the drain and chances are the water will drain fast.

Another natural method entails adding water pressure to the power of vinegar and baking soda. For this technique, Fox Valley plumbers advise that you start by pouring a cup of baking soda and another of vinegar down the drain. After that, place a drain cover on the drain opening so that water cannot flow into the drain. Once that is done, run some hot water and leave that water to sit for about 10 minutes.

This water will create a pressure difference between the interior of the drain and the air above. After ten minutes, remove the drain cover and the onrush of water into the drain may have sufficient power to dislodge the clog and push it through the drainage system.

Launch a Chemical Attack

The last trick up your sleeve when all the measures above don’t unclog the shower drain is a chemical drain cleaner purchased from a convenience store near you. Fox Valley plumbers caution that you should follow the usage instructions provided so that you don’t put yourself or the drainage system at risk. Repeat the use of a chemical drain cleaner after a day or so until the drain is working properly.

Contact Tureks Plumbing Services if the suggestions above if you’re still having a drain problem. Our experts will perform a thorough inspection and design the most cost-effective treatment plan to unclog the shower drain so that you can enjoy your showers without fearing that the water will flow out and flood the nearby rooms.

Continue Reading

Why Is My Toilet Bubbling?

Wednesday, April 17th, 2019

why is my toilet bubbling?Why Is My Toilet Bubbling?

Is your toilet bubbling or gurgling at random times even when you haven’t flushed it? You may be having a bigger problem on your hands… The following discussion suggests some of the remedies that you can use to fix this plumbing problem on your own before you call the professionals at Tureks Plumbing Services for help.

Why the Toilet May Be Bubbling or Gurgling

The root cause of a bubbling toilet is negative suction pressure inside the drain line. Fox Valley plumbers explain that this negative air pressure causes an airlock within the drain. Consequently, this airlock may be released, resulting in the air traveling back to the toilet.

The air then bubbles through the water in your toilet and that is why you will hear that random gurgling or bubbling sound. In some cases, the toilet may flush itself. Scary, huh?

Several remedies may fix this problem, depending on what exactly is causing the clog and where that clog is located in your plumbing system. Try the options below and see whether the bubbling stops.

Plunge the Toilet

The plumbers at Tureks Plumbing Services suggest that the first step to take to resolve the problem is by plunging the toilet. This should be done after blocking all the nearby drains, such as the sink, the shower drain, and the bathtub drain.

If you don’t block the other drains, the pressure created by the plunger will escape through those drains instead of acting on the clog that is responsible for the airlocks in the system. Use duct tape to seal or block the other drains and pump the toilet plunger 10 or more times. Be observant and find out whether the gurgling or bubbling sounds emerge again.

Check With Your Neighbors

A plumber in Appleton, WI also says that the clog triggering the bubbling in your toilet may be in the municipal sewer line. If that is so, then the problem will not be unique to your property alone.

So, you should contact your neighbors and find out whether any of them has also noticed that their toilet is bubbling or gurgling. If your neighbors are having the same probelm, then you should notify the municipal sewer company. They will send someone to check the sewer line and fix it at no cost to you.

Use a Plumber’s Snake

Another remedy that could fix the problem is by using a plumbing snake to remove any clog in the toilet drain. Plunging the toilet only works to dislodge smaller clogs. Using a plumber’s snake is a better option when the clog is tougher.

You can use either a motorized or a manual plumber’s auger/snake to unclog the toilet. Manual snakes are usually good when the clog is located close to the drain opening since the snake can only travel to a maximum of 15 feet.

Motorized augers are better for clogs located deeper in the system since they are longer and attack clogs with more power. You can rent this motorized plumbing snake from at a home improvement store near you instead of spending much more money to hire a plumber to unclog the toilet.

The head of the motorized plumbing auger is unlikely to pass through the toilet bowl drain, so you may need to remove the toilet and pass the auger through the floor drain. A Fox Valley plumber advises that you also run the plumbing snake through the cleanouts located at regular intervals along the sewer line in your yard if you suspect that the clog is farther out in the system.

If you fail to locate or open the cleanout, contact Tureks Plumbing Services and one of our plumbers will come over and help you to unclog the pipe.

Inspect and Clean the Vent Stack

The vent stack allows sewer gases in the plumbing system to escape to the atmosphere. If anything blocks the vent stack, negative pressure can build up inside a drain and trigger the toilet bubbling that you have been hearing.

To check the vent stack, climb onto the roof and tie a flashlight onto a wire or rope. Lower the torch into the stack and peer down to see where the blockage is located. Tree leaves and small animals (rodents, for example) are the most common culprits when vent stacks are blocked. Use a straightened coat hanger to break through the clog, or use a garden hose to force the clog down into the drain. A plumber’s snake can also clear this clog in the vent stack.

Call a plumber in Appleton, WI for help if you are queasy about the prospect of climbing onto the roof in order to check and clean the vent stack.

In most cases, one of the four options above is usually sufficient to put an end to the bubbling or gurgling in the toilet. If none of those solutions work, contact Tureks Plumbing Services for professional help. A sewer pipe may have collapsed, or tree roots may have partially blocked a sewer line. We are equipped to trace the problem to its root and fix it so that the abnormal sound you are hearing from your toilet is put to an end.

Continue Reading

7 Signs You Need to Replace Your Sump Pump

Wednesday, April 10th, 2019

Signs You Need to Replace Your Sump Pump - Tureks Plumbing Services7 Signs You Need to Replace Your Sump Pump

The sump pump in your basement plays a crucial role in evacuating any water leaks into this lowest point in your home. However, this trusted equipment can fail and result in serious water damage to your property. It is therefore advisable for you to educate yourself about some of the warning signs of a possible sump pump failure so that you can take action in time to avert a disaster. Here are the top signs that Tureks Plumbing Services advises you to watch for in order to replace your sump pump before the worst happens.

Types of Sump Pumps

Submersible Sump Pumps: Submersible pumps are submerged inside the sump pit. They are designed to withstand water damage while submerged in the pit. One major advantage of submersible sump pumps is that they operate noiselessly because the water surrounding them muffles any noise produced by the motor. Additionally, the motors of these pumps tend to be more powerful than those in pedestal pumps, and this makes them the best choice for locations where flooding is most likely to occur. The pumps are also out of the way, so you will not be inconvenienced as you rearrange things in your basement. However, the typical lifespan of submersible sump pumps is shorter than that of pedestal pumps.

Pedestal Sump Pumps: These pumps derive their name from the pedestal on which their motors sit above the sump pit. The pump has a hose that drops into the sump pit and the pump uses this hose to draw the water out. This pump is easier to service because the motor is in an accessible location outside the sump pit. However, plumbers in Appleton, WI say the pump isn’t as powerful as the submersible versions. So, you would be well advised to avoid installing this pump in your basement if the possibility of flooding is high in your area. Also, the pump can be an inconvenience while you rearrange things in your basement. Pedestal pumps are also noisy while operating.

Signs That Your Sump Pump Is Due for Replacement

1. Age

All machines eventually reach the end of their service life, and sump pumps are no different. Talk to a Fox Valley plumber about replacing your sump pump if it has exceeded seven years in service. This discussion is necessary because sump pumps rarely last beyond 10 years, so you are better off not taking chances with an aging pump.

2. Excessive Vibration

Sump pumps usually start vibrating when their impellers have been bent by debris that has been sucked into the pump. Bent impellers are no longer balanced on the shaft, so that throws the operation of the entire system out of whack. The strain caused by the imbalance of the forces exerted on the shaft is a recipe for serious pump problems later on. It is hard to straighten a bent impeller to its original dimensions, and that is why the best course of action to take is to replace the pump. Avoid this premature replacement by installing a filter to keep debris from being sucked into your sump pump.

3. Nonstop Operation

Switch malfunctions are the biggest cause of a sump pump that runs nonstop. For example, plumbers from Tureks Plumbing Services frequently find that the pump switch is unable to connect to the power source, thereby preventing the pump from cycling on. Alternatively, the float arm may be unable to move freely if the pump shifts within the sump pit. These switch defects account for a significant portion of sump pump defects.

A more serious problem that may prompt you to consider replacing the sump pump is if that pump keeps running nonstop when no other mechanical or technical defect can be identified. In such a case, the pump may have inadequate capacity to handle the load of water in your basement.

4. Visible Rust

Another reason why you should consider replacing your sump pump is when you see rust from this equipment. Rust could be coming from corroded terminals. Iron bacteria can also cause visible rust, so you should ask a plumber in Appleton, WI to take a look before you replace the pump prematurely.

5. Pump Runs for Abnormally Long

A properly sized pump normally runs for variable durations depending on how quickly water is accumulating in the sump pit. However, some pumps may run for an inexplicably long time before turning off. Such a scenario may point to the fact that the pump is undersized for the task at hand. For example, the water discharge network may have several bends that require a lot of power from the pump if the water is to flow through the pipes to the discharge point. Alternatively, the distance over which the pump is required to push the water may be so long that the pump could be straining to perform that task. The best option in such a case is to consult Tureks Plumbing Services so that an appropriately sized sump pump can be installed in the place of the undersized one.

6. Irregular Cycling

You should also have your pump checked if it keeps cycling irregularly. For example, does it start and run for just a few minutes, and then restart shortly after even when there hasn’t been any heavy rain? The float switch may be improperly set or there could be an electrical defect. A plumber in Appleton, WI can take a look and advise on the way forward, which may include replacing the pump.

7. Frequent Power Outages

It may also be necessary for you to consider replacing your sump pump if you have been having frequent power failures. Such incidents expose the electrical components of the sump pump to so much stress that the entire unit may soon fail. Install a surge protection system for your entire home and the sump pump before you procure a new pump.

It may be costly to replace your sump pump, but have you considered the likely cost of dealing with water damage to your property if the sump pump fails as a heavy bout of rain falls in your area? Don’t take that risk. Contact us at Tureks Plumbing Services for an assessment of the health of your sump pump. We shall fix what can be fixed or advise you to buy another pump if our experts realize that your existing pump can no longer be relied upon to evacuate water from your basement.

Continue Reading

Plumbing Mistakes New Homeowners Make

Thursday, March 28th, 2019

plumbing mistakes homeowners make - tureks plumbing services

Top 7 Plumbing Mistakes New Homeowners Make

The hassles associated with moving into your first home can drain you to the bone. It is therefore not surprising that you may easily make several rookie mistakes as you undertake some plumbing repairs to fix problems that went undetected when you were checking the home before buying it. Here are the top plumbing mistakes that the plumbing professionals at Tureks Plumbing Services regularly encounter with inexperienced first-time homeowners.

Thinking Any Tool Will Do

Many homeowners don’t have a sufficient collection of plumbing tools to attend to every plumbing defect that may arise. The temptation to improvise when you want a quick fix to a plumbing problem can, therefore, be high.

However, Fox Valley plumbers advise that you avoid using any makeshift tool when tackling plumbing problems because you risk making the problem worse or injuring yourself. For example, not any random tool that you find can cut a metallic plumbing pipe. Only undertake a plumbing project in your new home if you have the right tools for that job.

Taking Long to Fix Minor Defects

Another common mistake that plumbers in Appleton, WI see is that homeowners neglect to fix plumbing problems that they regard as minor. For example, you may not pay sufficient attention to a dripping faucet because you’re busy settling in. 

Those plumbing issues that you regard as minor can worsen and be costly to fix later on. For example, the dripping faucet can cause water damage to the floor and walls. A running toilet can flood. The list goes on and on. It is therefore advisable for you to fix each plumbing problem you notice as soon as possible so that it doesn’t get a chance to get any worse. If you can’t, then call a Fox Valley plumber for help.

Not Shutting the Water Off

It is very easy to get distracted by the task of putting together the different tools and materials that you will need for a plumbing project, and you forget what professionals consider to be Plumbing 101; turning the water off before you start.

Many homeowners confess that they learn this the hard way after getting started and having water gushing into their faces at high pressure. The resultant water damage from this mistake can be enough to make some people vow never to undertake any plumbing DIY project.

Don’t let this happen to you. Learn from the mistakes of others and shut the water off before you begin fixing any plumbing defect. Tureks Plumbing Services recommends that you locate the shutoff valve of the particular plumbing fixture that you want to fix so that the rest of the home can still have running water. For example, your kitchen faucet has a shutoff valve somewhere underneath the sink. The toilet also has a shutoff valve somewhere behind the toilet tank. Use the main shutoff valve located outside the home if the repair you want to undertake affects the main water line, or when you can’t locate the shutoff valve for the defective fixture.

Mismatching Plumbing Materials

One major shortcoming of DIY projects is that many homeowners don’t have enough experience to know that some materials don’t go well together. For example, did you know that you can trigger large scale water pipe corrosion if you join two pipe sections with a metallic connector that is not compatible with the pipes you are joining?

Talk to a plumber in Appleton, WI before you buy plumbing repair materials. That way the professional can guide you about which material is compatible with your home’s plumbing system. This guidance will save you from installing incompatible materials that can end up creating bigger problems.

Doing Unpermitted Work

The plumbing code usually stipulates which plumbing projects can be done without a permit and which ones require a permit. It is vital that you ascertain whether the project you want to take on requires you to get a permit from the authorities or you don’t need one.

Otherwise, unpermitted work can result in serious issues later on. For example, you may find it hard to get a buyer for that home if the pre-purchase inspection uncovers unpermitted work. You could also be prosecuted and fined if the authorities discover that you didn’t obtain the necessary permit required. It doesn’t hurt to talk to a Fox Valley plumber as you plan your plumbing project just to be sure that you won’t run into any problems later.

Careless Mistakes While Soldering

Some plumbing projects, such as repairing pipe leaks, may require you to do some soldering. Be extra careful if your project requires you to bring out your soldering torch. For example, ensure that you have covered or removed anything flammable from the work area before you start. Additionally, you should never set the torch down when its flame is still lit. Exercise caution and be aware of your surroundings at all times while you work. If you aren’t sure about your ability to implement all the necessary safety precautions, simply call a plumber in Appleton, WI for help.

Not Asking for Professional Help

It is okay for you to fix as many plumbing problems in your home as you can. Our team at Tureks Plumbing Services make it our duty to share useful information that can empower you to resolve plumbing problems without calling an expert each time a problem crops up. However, we always caution homeowners to know their limitations. Always ask for professional help when situations go out of your expertise. This is serious enough to warrant repeating; contact Tureks Plumbing Services each time you are faced with a plumbing problem that you are unable to fix on your own. We are available 24/7, so don’t put your safety and property at risk when we can sort the problem quickly.

Continue Reading

Top 6 Trenchless Sewer Repair Benefits You Should Know

Wednesday, March 20th, 2019

Trenchless sewer repair benefits

Top 6 Trenchless Sewer Repair Benefits You Should Know

Needing sewer line repairs on your property usually triggers groans from homeowners because of the inconvenience. However, new trenchless sewer repair technology is now available and you can opt for this modern way of fixing sewer line defects. Here are some of the key benefits of trenchless sewer repair that you can consider.

Trenchless Sewer Repair Is Less Invasive

Traditional sewer repair methods were a nightmare because of all the disruption that it would cause. For example, a large section of your yard can be dug up in order to fix a damaged sewer pipe.

Trenchless sewer repair has provided a solution to all this mess. In this method, only one or two access holes are dug and the repair is completed without further damage to your landscape. Ask a Fox Valley plumber about trenchless sewer line repair if you need sewer repair done.

Trenchless Sewer Repair Requires Less Time

Another major advantage of trenchless sewer repair is that less time is required to complete the project. An expert at Tureks Plumbing Services explains that there are two key reasons for this time-economy of the technique. First, the fact that minimal digging is needed saves time. Where plumbers need several days or weeks to dig up and then return the fill earth into the hole during traditional sewer repair, trenchless sewer repair needs just one or two access holes and the job can proceed swiftly.

The second reason why less time is required is that a significant portion of the work is done by machines rather than by humans. For instance, the process of inserting a liner inside a damaged sewer pipe is achieved using a machine. Traditional sewer repair often requires more man labor. For instance, workers will have to get inside the pipe in order to repair it, and this takes more time.

Trenchless Sewer Repair is Less Expensive

Initially, it is easy to conclude that trenchless sewer repair is more expensive compared to traditional sewer repair. However, a closer analysis shows the reverse to be true. For example, a plumber in Appleton, WI explains that traditional sewer repair may seem affordable but when you factor in the costs you incur to restore your yard to the state it was before the repairs, then the option doesn’t seem so affordable after all. The longer lifespan of the completed trenchless sewer repairs also spreads out the cost and makes the option affordable in the long run.

Higher Quality Work

Trenchless sewer repair utilizes high-quality materials that make the completed job better than traditional plumbing. For example, cured in place pipes (CIPP) are used to fix damaged pipe sections. These pipes have no seams. So, they stand a high chance of lasting much longer than metallic pipes which have joints. In fact, many trenchless sewer repair firms often say the pipes will last for 50 or more years! This is due to the high quality of the materials used during trenchless sewer repair.

Improved Sewer Function

The latest technology that is used during trenchless sewer repair ensures a successful repair. For instance, the seamless CIPP pipes used to remove the places where solids flowing through the system could snag and cause a clog to develop. You should, therefore, talk to a Fox Valley plumber about trenchless sewer repair if you would like a more efficient system once the repairs are completed.

Convenience

As already mentioned, traditional sewer repair takes several days or even weeks to be completed. Can you imagine living in your home for all those days when you cannot use the toilet or shower? You will most likely find a temporary place to live, such as a hotel, while the plumbers complete the repairs. Such inconveniences can disrupt your life and make it harder for you to do the things that you normally do, such as focusing on your job while at work. Trenchless sewer repair spares you those inconveniences since the sewer system will be back to normalcy in a short time.

Trenchless sewer repair may not be appropriate for all situations. For example, the damaged pipe section may be on an undeveloped section of your property where traditional trenching wouldn’t cause any serious damage. It is therefore advisable for you to talk to an expert at Tureks Plumbing Services so that the suitability of this method can be ascertained.  

Continue Reading

How to Clean Your Dishwasher

Wednesday, March 6th, 2019

How to clean your dishwasher - Tureks Plumbing Services

How to Clean Your Dishwasher

You may become increasingly uncomfortable about using utensils that have been cleaned in a smelly dishwasher, and you may be wondering what you can do to fix the problem. The experts at Tureks Plumbing Services share some simple tips and tricks that you can implement to get rid of dishwasher odors.

Scrub the Dishwasher

The drain filter is the most likely cause of the smells coming from your dishwasher. Access this component by removing the bottom rack of the dishwasher and then twist the filter until it comes out of its position. Use a brush to scrub it thoroughly so that all food particles are dislodged from it. Fox Valley plumbers also suggest that you scrub the door and the interior walls in order to eliminate any food particles that may be stuck there.

While at it, remove the gaskets on the dishwasher door and give them a scrub. The gaskets can trap food particles, and over time, those particles will start giving off a nasty smell. Tureks Plumbing Services reminds you to clean the dishwasher racks too. Remove them from the dishwasher and clean them from the sink. Scrub them thoroughly until they are spotless.

This thorough cleaning of the dishwasher is likely to get rid of the root cause of the smells. Our friends at Maid for Muddy Paws, who offers cleaning services in Katy Cypress, add that you are less likely to experience the same problem soon after.

Use Vinegar and Baking Soda

The white vinegar in your pantry can come to the rescue once odors start emanating from your dishwasher. Plumbers in Appleton, WI recommend that you place a cup of this vinegar on the upper rack of the dishwasher. Make sure your dishwasher is empty before you use this remedy. Next, run a full cleaning cycle. The vinegar will break up all the food particles that could have caused the smell.

The beauty of using vinegar is that its strong smell will quickly dissipate as your dishwasher dries once you open it. Similarly, the odors will also be long gone by the time the dishwasher dries.

For additional sanitization, sprinkle some baking soda over the entire bottom section of the dishwasher. A cup will suffice for this purpose. This time around, run the dishwasher at the hottest setting for the shortest time possible. The heat will make the baking soda to dissolve, and your dishwasher will be odorless at the end of that cleaning cycle.

Refer to the User Manual

Another way to get rid of the odors coming from your dishwasher is by reading the troubleshooting section of its manual. Fox Valley plumbers recommend this step because all manufacturers include specific steps that you can take if you notice odors coming from your dishwasher.

For example, the drain hose may be partially blocked, hence trapping water there and triggering smells with time. Improper drain hose installation can also gradually trigger odors since water from the sink can back up into the drain and remain stagnant there until odors develop. Tureks Plumbing Services, therefore, suggests that you read the troubleshooting chapter and take the suggested steps if the dishwasher remains smelly after you have cleaned it using the methods described earlier.

An electrical problem can also trigger an odor to come from the dishwasher, especially when there is a poor connection. Check the junction box under the door of the dishwasher. Call an expert, such as an electrician, if you suspect that an electrical defect may be responsible for the odor.

It may be time to involve the experts at Tureks Plumbing Services if the smells remain even after you have tried the solutions above. A clog may be further along the drain, and our plumber will locate it in no time. Schedule a service call today so that the inconvenience of the dishwasher odor can be eliminated.

Continue Reading

Common Objects That Clog Toilets

Wednesday, February 6th, 2019

common objects that clog the toilet - tureks plumbing

Common Objects That Clog Toilets

It is sad to realize that many homeowners spend a lot of money each year to hire plumbers to unclog their toilet or plumbing system. It’s unfortunate because a significant fraction of those emergency plumbing calls could have been avoided if only the homeowners and their family members knew that they shouldn’t flush certain common objects down the toilet. Here are the most common objects that clog toilets. 

Excessive Amounts of Toilet Paper

Most people instinctively know how much toilet paper to use and flush down the toilet. However, kids may not have such rationality, and they will quickly turn flushing toilet paper into a game. When a large amount of toilet paper is flushed in one go, it can bunch itself into a tight ball as it travels down the drain. That ball of toilet paper will not degrade as rapidly as expected, and a clog may develop at that point where the ball has snagged. Fox Valley plumbers advise parents to teach their kids to refrain from flushing excessive amounts of toilet paper.

Don’t Flush Hair 

Are you in the habit of cleaning your pet dog in your bathtub and then letting the fur flow down the drain? Or do you collect that fur and flush it down the toilet? Whether it is human or animal hair, never flush it down your toilet. Many plumbers in Appleton, WI admit that the number one cause of shower drain clogs is hair. A better option is to place a strainer on the bathtub drain so that all the hair is collected and disposed of properly with the trash. Don’t even think of dumping it in the toilet!

Don’t Flush Feminine Hygiene Products

It is common to find signage in public restrooms reminding users not to flush feminine hygiene products like tampons and sanitary towels down the toilet. However, some people don’t implement the same advice at home. Those products aren’t biodegradable, and they will clog the toilet sooner rather than later. Always have a trash can in the bathroom so that such products can be disposed of with the trash instead of finding their way into the toilet. The number of times you have to call a Fox Valley plumber for help regarding a clogged toilet will reduce significantly once you make this one change.

Don’t Flush Paper Towels

There’s a reason why a trash can is placed close to the sink where you wash your hands after using a public restroom. That can is intended to be a receptacle for the paper towel you use to dry your hands. While paper towels are made from, well, paper, they are thick and will not break down easily when flushed. In case you weren’t aware that paper towels shouldn’t be flushed, now you know. Talk to a plumber in Appleton, WI about the plumbing problems caused by paper towels if you still have doubts about the dangers of flushing paper towels.

Don’t Flush Toys

This one seems obvious, but curious and playful kids will not hesitate to turn flushing toys into a game. All it takes is just one toy to get stuck anywhere in the plumbing drains, and you will have a major clog in the system. As you know, kids will always be kids, so take the precaution of having someone to supervise them at all times if they have toys while in the bathroom.

Don’t Flush Baby Wipes and Diapers

You may think that flushing diapers may be a quick fix to the odors, but that quick fix will cost you once the toilet develops a clog. The same risk will take place when you flush baby wipes or any type of wipe. Don’t believe it when the packaging of the wipes says that they are “flushable.” What the manufacturers mean differs from what your plumber in Appleton, WI will regard as flushable. This is because anything you flush should degrade in a short time so that blockages don’t develop in the plumbing system.

There are many other common objects that you should refrain from flushing down the toilet. A simple way to remember them all is to adopt a simple rule that you and your family members should only flush toilet paper and nothing else. Call Tureks Plumbing Services if you suspect that a clog is preventing your toilet from draining as quickly as it should. We shall send an experienced Fox Valley plumber to assess the situation and perform the needed work before your toilet backs up.

Continue Reading